Flipsky AntiSpark Switch Smart Enhanced 200A for Electric Skateboard /Ebike/ Scooter/Robots

$130.99 $83.99

Out of stock


Sale ending in


Checkout safely using your preferred payment method

american expressapple paydiscovergoogle payjcbmasterpaypalvisa
Item Brand:Flipsky
Item Name: Anti spark Switch Smart Enhanced 200A
Material:Metal and plastic
Color:As the picture shown
Product Weight:About 50g
Fit For:Electric Skateboard /Ebike/ Scooter/Robots

Hardware: V2.2
Max voltage: 13S (60V)
Continuous Current: 150A , Max Current: 200A
Mosfets: NVMFS5C628NLs
LED button diameter:12mm, cable length: 250mm
PCB thickness:4 layers*9oz copper=36oz copper
PCB size: 40mm*32m

Enhanced Features:
High Side Switching -> Much safer to use with multiple ESCs and other devices.
In-rush current limiting.
RC delay network restricts inrush current to safe levels.
dV/dt is ~100V/s (This is considered VERY slow for power electronics. Fast would be 50,000,000V/s). At 6,000 uF output capacitance, this is an inrush current of 600mA.
Smart Power on/off
Roll-to-start. Has 12 second blanking timer after turn off. Can still be turned on by switch during this period.
Auto-turn-off. Will turn off automatically after 20 minutes. The output voltage must vary by at least 500mV within any three second interval to reset the turn-off timer.
Support momentary push button. Hold for 0.3s to turn on, 1s to turn off. Holding it down will cycle it on then off.
High power, 150A Continuous.
Very low idle power draw, ~300uA, will last months on battery.
Package included:
1X Anti spark Switch 200A

1.Preventing a small spark may cause explosions in some spark-sensitive areas.
2. Add copper bars for better heat dissipation and over-current flow.
3.Anodized aluminum Heatsink with lots of notches for better heat dissipation.
4.Add silicon glue to fix the LED button cable with the heat shrink.

Do not peel off the heat shrink.There’s no screw to lock the heatsink and PCBA. Only the heat-transfer silicon pad is naturally sticky to heatsink and PCBA.
No short circuit protection, DO NOT short circuit output!
No reverse polarity protection. DO NOT plug in backwards.
Recommended to keep output capacitance under 6,000 uF. Proper operation cannot be guaranteed at higher capacitances.
Do not Hot-Swap. Try to make sure everything is off before connecting and removing. If need be, unplug from battery first, wait for ESCs to turn off, then unplug ESCs. Do the reverse for plugging in, plug in ESCs first before plugging the switch into the battery.
Engineers have thoroughly tested prototypes; however, this is still a new design and a first production run, please exercise extreme caution (as one would normally do with any electric vehicle) when using this device.
Do not attempt to reprogram the MCU unless otherwise advised. Doing so will void any warranty and also put the switch at great risk of failure.

Please allow 7 - 12  days for your order to arrive. We source products from all over the world to bring you epic offers and the lowest prices. This means sometimes you have to wait a little longer to get your order but it's always worth it!

Our policy lasts 30 days. If 30 days have gone by since your purchase, unfortunately we can't offer you a refund or exchange. To be eligible for a return, your item must be unused and in the same condition that you received it. It must also be in the original packaging.

Not enough items available. Only [max] left.
Add to WishlistBrowse WishlistRemove Wishlist
Shopping cart

Your cart is empty.

Return To Shop

Add Order Note Edit Order Note
Add A Coupon

Add A Coupon

Coupon code will work on checkout page

Flipsky AntiSpark Switch Smart Enhanced 200A for Electric Skateboard /Ebike/ Scooter/Robots

$130.99 $83.99